Get The App From Play Store!

Skip to main content

BLACK FRIDAY EVENT use code BF25 at checkout to SAVE 25% when you spend £30 or more excluding delivery.

BLACK FRIDAY EVENT use code BF25 at checkout to SAVE 25% when you spend £30 or more excluding delivery.

Dishwasher Heating Element - 2000W Stock Number: ES544551

Genuine part for select models of Zanussi, AEG and Electrolux dishwashers

Read more

Manufactured by Zanussi

(This part fits select models)

Will this part fit my Appliance?

Does it fit?
Enter your model number and select from the below list
Need help finding your appliance model number?

Check this part fits your appliance

2. Enter your model number

Dishwasher Heating Element - 2000W

If you notice that the water in your dishwasher is not at its usual high temperature, there could be a problem with the heating element. With this replacement heater from our range of dishwasher spares, eSpares could soon have you back to a dishwasher with hot water again - for a better cleaning performance on your dishes and cutlery!

Specifications:
  • Type: Flow-through
  • 2000 Watts
  • Diameter: 32mm
  • 230 Volts

Please note: That this part is PNC number dependent.

Genuine part for select models of Zanussi, AEG and Electrolux dishwashers.

Please contact our call centre with your model and PNC number so we can advise the correct spare for you. 

Ask a Question

16 Questions and 20 Answers

Received flow through heater from you for the above appliance. Prompt delivery thanks. Fitted it this morning but still not getting hot water. What is this PNC that is required? Have I purchased the wrong heater?

By Dave - Ossett, West Yorkshire - 09 December 2013
  • Parminder from eSpares
    Parminder at eSpares says...

    We recommend checking our advice centre article for more information on dishwasher heating/drying problems: www.espares.co.uk/advice/symptom/my-dishwasher-is-not-heating-up

  • I have just fitted a heater purchased from you and it still does not heat water. It is a ZDT6053 dishwasher and I fitted P/N 000050297618006, Is there a thermostat somewhere or are they built into heater? If so what else can it be. I goes through the full cycle but does not heat or dry. By BK - Ireland - 10 September 2018
  • Chris from eSpares
    Chris at eSpares says...

    The PNC code is the production number and is required for some parts, However it would not stop a heater that fitted from working. The fault is likely to be either the control board or thermostat if fitted.

Answer this question

Just purchased and recieved heating element for John Lewis dishwasher. No fitting instructions with it. Phoned help line to ask for guidance told to try Utube for video. none found. Do you have any fitting instructions you can email me? Paul Mc

By Paul Mc - Liverpool - 16 May 2011
  • Rory [at eSPARES]- I think you are mistaking this unit for the loop type of element which sit inside the washing chamber. This one for the JLDWW1201 is an inline unit, totally hidden from normal view. The heater element is located right at the back of the machine (lower right when viewed from the front) and you can't gain good enough access through the front panel of the dishwasher because the water filter/sump and main pump are in the way. The best access is when the right side panel is removed. Even then, access is not very good because the heater element is horizontally installed with the far hose clip hard to get at. Poor design from a replacement point of view. By Mark - - 06 June 2011
  • Rory from eSpares
    Rory at eSpares says...

    Hi Paul Mc. Unfortunately we don't have video advice for fitting a dishwasher element, however it's not too difficult. You'll need to remove the panel below the door of the dishwasher and remove the connections to the element from that side. Then, remove the lower basket, and you'll be able to access the element and remove it.

Answer this question

water not heating I think it is this element

By malg - - 21 May 2010
  • On my AEG 50860, the element is at the back of the dishwasher. If you remove the bottom back panel you will see it, attached to its input/output pipes by two steel circlips. You'll need a pair of molegrips or strong pliers to undo the circlips. By Anonymous - London - 11 October 2010
  • eSparesMalindi from eSpares
    eSparesMalindi at eSpares says...

    We cannot give out technical advice unfortunately. Please contact an engineer for support with identifying the fault with your appliance and for fitting of the replacement part.

Answer this question

can you suggest the next move ?

By Glynne Jones - consett - 26 May 2017
  • Dean from eSpares
    Dean at eSpares says...

    For information on this problem see our diagnosis video: How to Diagnose Dishwasher leaking and heating problems http://www.espares.co.uk/advice/3/2083

Answer this question

What should I replace? water heater or the thermostat. thanks

By AD - Glasgow - 13 March 2015
  • Chris from eSpares
    Chris at eSpares says...

    For information on this problem see our diagnosis video: How to Diagnose Dishwasher leaking and heating problems http://www.espares.co.uk/advice/3/2083

Answer this question
See all questions and answers

Will this part fit my appliance?

Check Now

Dishwasher Heating Element - 2000W

£58.99
(inc. VAT)
£58.99