Tumble Dryer Heater Element Irca S 9276 845 - 2100W Stock Number: ES956282
Genuine spare part for select models of Hoover, Candy and Maytag tumble dryers
how can I open my hoover dryer to access the heating element so that I can test it to see if its blown 1 Answer
-
Chris at eSpares says...
In order for us to answer your question or source the exact part you require please provide us with the following information: Appliance make, model and serial number of your appliance. For further help visit the "Finding Model Numbers" page on our website here: http://www.espares.co.uk/findingmodelnumbers. Alternatively please copy and paste this link into your web browser.
My Candy Goc58F was failing to heat up and stopped after a few minutes with all lights flashing I have purchased a new element from yourselves and fitted it but the problem persists any ideas? 1 Answer
-
Chris at eSpares says...
As this is a condenser dryer it suggests if there is heat present when you try it that the problem is related to the pump not emptying the reservoir into the water container. For more information see our video: http://www.espares.co.uk/advice/9/2050/how-to-diagnose-tumble-drier-drying-and-heating-problems
The heater element has failed, both sensors on the heater casing are ok. Is there anything else that could be wrong or require checking as the machine is not yet two years old
-
Chris at eSpares says...
It is important to allow tumble driers to complete there cycle as many will run a cool down cycle to remove the heat from the element. If stopped early this can cause the element to overheat and fail. Check the condenser if fitted is not blocked with fluff as this too can cause overheating and failure.
Is there any other way to access the heater element connectors without removing the drum assy in a Candy GOC580C tumble dryer? 1 Answer
-
Chris at eSpares says...
If you gently tug the wires as they pass into the cabinet you may see a small plastic peg passing through the back move. If you release this peg by gently squeezing it with pliers and pushing through you will have enough cable to carefully pull through the whole and reach the connectors. Refit these connectors to the new heater and refit the heater. Then remove top fascia and front as previously described to reach through and refit cable grip to cabinet to prevent cable damage by drum.
-
Chris at eSpares says...
To remove the drum you have to take off the top panel, the control panel and the front panel. Then remove the front drum support frame by removing the four screws and lifting 10mm and hinging out from the bottom. Reach under the drum and flip the belt off the tensioner pulleys, then you can remove the rear duct and screws that fix the bearing plate to the cabinet rear. Once all that is done the whole drum and bearing assembly can pass through the cabinet front.
how many ohms should the resistance of the heater element be on the Hoover 2100 Watt Tumble Dryer Heat Element for VHC381/1-80? thanks
-
Chris at eSpares says...
The resistance of an element producing 2100 watts of heat from 230 volts should be around 25 ohms. Note as most driers have high and low heat settings it is normal to have to elements that are in parallel to produce this resistance. individually they will read approximately double this figure.
we purchased the parts from Espares so we just need to replace it but when we removed the old heat element, there are a few connectors that is connected inside the machine which we don't know which pannel to remove to connect it. Our dryer model number is VHC691 B - help
-
Chris at eSpares says...
Safety first disconnect the electricity before starting the repair.To fit this heater there is a grommet that the connections pass into the machine. remove this gromit and release the cable grip barb near the hole to allow the wires and connectors to be drawn through the hole. Swap the connections over one at a time to the new heater and mount onto the rear panel. To refit the cable clip back to prevent wires from catching the drum you may have to remove the top and front and reach through to the back panel (not easy).
hoover vision HD 8kg vhc 380 and it stops after 5 mins, instead of the display saying over 60 mins left of drying time it stays on start, comes on for 5 mins then goes off with the start light still on. if i want to restart it i have to turn the machine off and back on i cant just press start otherwise it just makes a slight clicking noise and wont come on.
-
Chris at eSpares says...
It is likely the appliance is identifying a problem and switching off. By the sound of it I would suspect a heat problem and would check if you can feel any warmth in the drum when it stops.
-
Chris at eSpares says...
The cables for the heater are attached to the back wall of the dryer to prevent them catching the drum. You may have to take the drum assembly out to access them correctly.
Will this part fit my appliance?
Check Now